Reading dimension in datasheet – electronics.stackexchange.com


Rineau
25/12/2015 9:47 am
HOME » Development

This is my first time making pcb layout. I am also quite unfamiliar with datasheets. I am using DS90LV019 (the figure is attached below). What is the actual length of this IC. Does ...

Related to : Reading dimension in datasheet – electronics.stackexchange.com
Reading dimension in datasheet – electronics.stackexchange.com
25/12/2015 9:47 am by Rineau in Development
This is my first time making pcb layout. I am also quite unfamiliar with datasheets. I am using DS90LV019 (the figure is attached below). What is the actual length of this IC. Does ...
How do I make sure my electronics design is good from manufacturing perspective? – electronics.stackexchange.com
22/12/2014 10:05 am by baylisscg in Development
I am a beginner in electronics design. I have some experience with fairly complex PCB design. I want to design a product that will hopefully sell a lot. How do I ensure that the design is inexpensive ...
Why do electronics have a low temperature limit? – electronics.stackexchange.com
15/12/2014 4:05 am by digiram in Development
Apart from condensation why do electronics usually have a low temperature limit? For example my laptop says something along the lines of -10-75°C temperature while in use. I can understand the high ...
What is a DC DC controller? – electronics.stackexchange.com
22/12/2014 4:05 pm by VirtualLarry in Development
I have heard about DC DC converters and I understand what they are but what is a DC DC controller? What is the difference between the two? Like this LM5085, I cannot understand the major difference ...
4 Mbit != 512 Kb? – electronics.stackexchange.com
14/11/2014 4:05 pm by LukeG in Development
I'm working with a fujitsu microcontroller and I think I'm a bit rusty on the following details, that's why I'm asking this question. I have the following specs: 4M-bit flash memory • Built-in ...
Why use a 0 ohm resistor? – electronics.stackexchange.com
12/12/2014 1:05 pm by Pat in Development
My customer's schematic uses a 0 ohm resistor for connecting analog(AGND) and digital (DGND). I think it is for testing, current measurement , fuse, jumper, test point etc but is there another ...
Best way to get 256 io pins? – electronics.stackexchange.com
25/12/2014 1:05 am by fayoh in Development
I'm connecting to an arduino or raspberry pi and would like to have 256 io pins. I found a 16bit io expander which has 8 unique addresses for 128 but that's the max I can do on i2c. Any other thoughts ...
Using two 14 AWG wires instead of one 12 AWG – electronics.stackexchange.com
3/1/2015 4:05 pm by 007ELmO in Development
I do understand there are many factors when choosing what AWG wire, however by the charts, tools, and info I have found, using two 14 AWG copper wires should be equal to a single 8 AWG wire. 8.025 AWG ...
How does the controller know when to jump to the ISR? – electronics.stackexchange.com
16/12/2014 7:05 pm by Steve O. in Development
I am talking about things at the core level. As far as I understand, the controller core just executes instructions which are fetched from the memory (Fetch - Decode - Execute). When an Interrupt ...
Use Cases for an External ADC – electronics.stackexchange.com
10/12/2014 4:05 am by fletchnj in Development
Most Microcontrollers (uC) have an Analog to Digital Converter (ADC) as part of their peripheral set, which is phenomenal as this integrates two components into a single package. These ADCs are ...
Privacy Policy - Copyrights Notice - Feedback - Report Violation - RSS 2014 © bighow.org All Rights Reserved .